NH3 Jobs

Manufacturing Engineer

A
AiStone Computing IncFremont, CA1w ago
Full timefulltimeEngineer

Compensation

$100,000-$150,000/yr
Functions
MaintenanceControlsSafetyReliability

The Role

Position SummaryThe Process Engineer is responsible for developing, implementing, optimizing, and sustaining manufacturing processes to achieve high product quality, improved production yield, increased productivity, and cost efficiency. This role leads process flow chart design, equipment and tooling development, Standard Operating Procedure (SOP) creation, New Product Introduction (NPI), and continuous improvement initiatives.The ideal candidate has strong engineering fundamentals, hands-on manufacturing experience, analytical problem-solving skills, and the ability to collaborate with cross-functional teams to establish robust, repeatable, and scalable manufacturing processes.Key Responsibilities1. Process Flow Chart Design and Optimization

  • Develop, document, and maintain manufacturing process flow charts from raw material preparation through final inspection and product shipment.
  • Define process sequences, production steps, inspection points, critical process parameters, quality checkpoints, and material flow.
  • Identify process bottlenecks, inefficiencies, redundant operations, and potential quality risks.
  • Optimize process flow to improve cycle time, throughput, labor efficiency, work-in-process (WIP), and overall production capacity.
  • Conduct process risk assessments and support the development of Process Failure Mode and Effects Analysis (PFMEA), control plans, and related process documentation.
  • Ensure process flows align with product specifications, engineering requirements, quality standards, and manufacturing capabilities.
  • Collaborate with Design Engineering, Quality, Production, and Supply Chain teams to implement process changes and drive continuous improvement.

2. Equipment and Tooling Development

  • Define equipment, tooling, fixture, and manufacturing workstation requirements based on product design and process specifications.
  • Evaluate, select, and qualify production equipment, tools, fixtures, jigs, and automation solutions.
  • Develop equipment specifications, tooling concepts, and technical requirements in collaboration with equipment suppliers and internal engineering teams.
  • Lead equipment installation, setup, debugging, process validation, and production readiness activities.
  • Establish equipment operating parameters, preventive maintenance requirements, calibration needs, and troubleshooting procedures.
  • Conduct equipment capability studies and verify process repeatability, reproducibility, and reliability.
  • Identify opportunities to improve equipment utilization, reduce downtime, and enhance manufacturing safety and ergonomics.

3. SOP and Manufacturing Documentation

  • Develop, review, and maintain SOPs, work instructions, process specifications, setup sheets, inspection procedures, and troubleshooting guides.
  • Define standard operating conditions, process parameters, acceptance criteria, and operator responsibilities for each manufacturing step.
  • Ensure manufacturing documentation is accurate, controlled, accessible, and compliant with applicable quality management system requirements.
  • Train production operators and technicians on new processes, equipment operation, tooling usage, and updated work instructions.
  • Implement document control and change management procedures to ensure consistent execution across production shifts and manufacturing lines.
  • Audit process compliance and update documentation based on engineering changes, quality findings, and continuous improvement activities.

4. New Product Introduction (NPI)

  • Lead manufacturing process development and industrialization activities for new products from prototype builds through pilot production and mass production.
  • Review product drawings, specifications, Bills of Materials (BOMs), and design requirements to assess manufacturability and production readiness.
  • Collaborate with Design Engineering, Product Engineering, Quality, Supply Chain, and Operations teams to identify manufacturing risks and resolve design-for-manufacturing (DFM) issues.
  • Develop process flow charts, equipment and tooling plans, SOPs, inspection methods, and process validation plans for new products.
  • Plan and execute Engineering Validation Builds (EVT), Design Validation Builds (DVT), Production Validation Builds (PVT), pilot runs, or equivalent build phases, as applicable.
  • Establish baseline process parameters and validate product quality, process capability, cycle time, and production yield before mass production.
  • Track and resolve issues identified during prototype, pilot, and pre-production builds.
  • Ensure production lines, tooling, materials, documentation, operator training, and quality controls are ready for production ramp-up.
  • Support engineering change implementation and ensure changes are properly validated and documented.

5. Yield Improvement and Continuous Improvement

  • Monitor and analyze production yield, first-pass yield (FPY), defect rates, scrap, rework, and process perform